Send Message
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Shenzhen Hong Ye Jie Technology Co., Ltd
English
High-Humidity Gel Sealing for Food Plant AHU and Cooling Coil Filters
INTRODUCTION The global food safety testing and controlled environment market is projected to reach USD 22 billion by 2027, driven by mandatory FSSC 22000, BRCGS, and SQF certification requirements that food manufacturers must maintain to access export markets in the EU, North America, and Japan. Airborne contamination control is a critical audit focus area, and filter sealing integrity directly impacts HACCP validation outcomes. Food plant engineering managers are moving away from gasket-based...
Skin-Friendly Jelly Gel Materials for Fever Cooling Patches and Medical Aesthetic Cold Pads
INTRODUCTION Reusable silicone cooling products are replacing disposable hydrogel patches in family and clinic markets because they combine cooling comfort with years of reuse, and brands compete on skin-safety documentation for postpartum and pediatric use. Hong Ye supplies skin-contact transparent gel with biocompatibility data, ISO 10993 support and small-kit development packaging, helping Chinese manufacturers launch compliant reusable cooling products. The market favors suppliers who can...
Low Modulus and Stress Relief Principles in Soft Potting for Precision Electronics
INTRODUCTION Precision electronics fail under encapsulation stress through three mechanisms: cure shrinkage pulling on joints as the material sets, coefficient of thermal expansion (CTE) mismatch between silicon dies (about 3 ppm/C), FR-4 boards (14-17 ppm/C), aluminum housings (23 ppm/C) and potting compounds (100-250 ppm/C for epoxies), and vibration fatigue hardening with age. Hard materials constrain movement, so thermal cycling converts CTE mismatch into cyclic stress on solder joints...
Waterproof Jelly Gel Potting for Electric Two-Wheeler and Vehicle Controllers and BMS
INTRODUCTION Electric bicycle and scooter controllers, light EV BMS units and motor drivers sit low on vehicles where rain, road splash, car-wash jets and road salt attack continuously, while vibration from rough roads and vibration from the motor itself shake solder joints. Low-cost designs use conformal coating or hard epoxy; coating wets but leaves pinhole paths after thermal aging, while epoxy traps heat from MOSFETs and makes warranty repair impossible. Hong Ye HY-9405 jelly gel gives the...
Soft Gel Potting for Smart Home Sensors: Temperature, Humidity, Door and Water Leak Devices
INTRODUCTION Smart home device makers compete on reliability in rooms where moisture exposure is routine, and online retail return rates punish even small waterproofing failures. Selective gel potting has moved from upmarket products to mainstream sensor lines as automated dispensing brought per-unit cost to cents. Hong Ye supplies small-kit to drum volumes, RoHS/REACH documents and masking/dispensing process guidance for high-volume OEMs. The market favors suppliers who understand which sensor...
Weather-Resistant Gel Potting for Photovoltaic Inverters and Power Optimizers
INTRODUCTION String inverters, microinverters and power optimizers sit under solar modules or on outdoor walls for 25-year design lives, facing daily thermal cycles from minus 40 nights to 80C enclosure peaks, condensation, rain and dust. Power boards carry high-voltage DC terminals, inductors and SMT controllers where moisture-driven corrosion and solder fatigue drive field failures. Hard potting gives weather protection but its modulus stresses large components through thousands of cycles and...
Winter Gel Sealing Practice for Filters in Extreme Cold Regions
INTRODUCTION Winter construction in northeast China, Mongolia, Siberia and the Nordic countries faces channel temperatures near or below zero, where two-component silicone gels mix thickly, flow slowly and cure far slower than their 25C ratings. Hong Ye HY-9400 is engineered to remain usable with disciplined cold-weather practice: store pails indoors at 15-25C, temper components to 20C or warmer before mixing, warm channels with hot-air blowers to above 10C, and pour in smaller sections so the...
Extending HEPA Service Cycles: Lifecycle Cost of Self-Healing Gel Seals
1 Introduction Procurement decisions on filter sealing often focus on per-kilogram sealant price, but lifecycle accounting shows the opposite picture. A gasket-sealed terminal needs gasket replacement at every filter change or every certification cycle, with labor, compressed hardware checks and recurring leak-test failures; a PU gel bed may need re-pouring after it hardens or tears. Hong Ye HY-9400 jelly gel is poured once: over a 10-year cleanroom life, filters may change 10-20 times, and...
Salt-Spray-Resistant Gel Sealing for Marine and Offshore HVAC Filters
1 Introduction Commercial ships, naval vessels, FPSOs and offshore platforms operate HVAC and machinery-space ventilation systems with coalescers, moisture eliminators and HEPA filters that protect crew quarters, control rooms, engine electronics and gas detectors. The operating environment is aggressive: salt fog at 35 parts per thousand salinity, relative humidity above 95 percent, continuous engine vibration, hull flexure and installation on tilted or overhead channels. Hong Ye HY-9400 is a...
Swimsuit Gel Insert Resistance to Chlorine and Salt Water
1 Introduction Swimsuit gel pad chlorine salt water resistance. Hong Ye HY-9409 has become a benchmark grade for bikini and one-piece swimsuit manufacturers in coastal garment clusters. After 500 hours in 50ppm chlorine and 1000 hours in 5 percent salt water, HY-9409 shows no swelling, hardening or tack loss. As a two-component addition-cure platinum jelly gel mixed 1:1 by weight, HY-9409 offers a viscosity of 2200+/-400 mPa.s, 20 to 40 minute operation time and 4 to 6 hour room temperature...
Silicone Bra Pad Jelly Gel Material Selection Guide
Summary This article provides a technical analysis of silicone bra pad jelly gel material selection guide, covering material properties, installation procedures, key performance parameters, and quality assurance to support engineering and procurement decisions. 1 Introduction Silicone bra pad jelly gel material selection. Hong Ye HY-9409 has become a benchmark grade for push-up bras, sports bras and bridal lingerie brands serving global markets. HY-9409 offers 150 penetration, 600 percent...
Hongye Silicone Launches High‑Humidity Resistant Mold Silicone
Keywords: Hongye Silicone, high humidity resistant mold silicone, RTV‑2 liquid silicone, handicraft mold material Key Sentence: Hongye Silicone introduces high‑humidity resistant RTV‑2 mold silicone, delivering stable demolding performance for handicraft manufacturers in humid tropical regions. Hongye Silicone releases improved high‑humidity resistant RTV‑2 mold silicone, aiming to solve unstable curing and soft surface issues faced by mold‑making factories located in tropical and coastal...
Solar PV Junction Box IP68 Gel Sealing Solution
Summary This article examines market trends and demand drivers for solar PV junction box IP68 gel sealing solution, including industry growth factors, supplier selection criteria, and global adoption trends. 1 Introduction Solar junction box IP68 gel seal. Global demand for premium two-component jelly gel is growing at double digit rates, driven by cleanroom construction in semiconductors and biopharma, smart meter rollouts, automotive electronics electrification, and the continued expansion...
Automotive ECU Low Stress Soft Gel Encapsulation Trends
Summary This article provides a technical analysis of automotive ECU low stress soft gel encapsulation trends, covering material properties, installation procedures, key performance parameters, and quality assurance to support engineering and procurement decisions. 1 Introduction Automotive ECU soft gel encapsulation. Hong Ye HY-9405 has become a benchmark grade for transmission control units, BMS and ADAS sensors with fragile ceramic capacitors. Soft gel reduces stress on MLCCs by over 70...
Low‑Viscosity Mold Silicone Improved
Keywords: Hongye Silicone, low‑viscosity mold silicone, fine detail casting, Huizhou silicone factory Core Sentence: Hongye Silicone optimizes low‑viscosity mold silicone formula to deliver sharp detail replication for resin, gypsum and craft casting projects. August 27, 2026 — Many craft manufacturers encounter incomplete pattern reproduction when casting complex‑texture artworks. Excessively high viscosity silicone cannot flow fully into tiny grooves, resulting in defective finished molds and...
Cosmetic Factory Cleanroom Gel Seal Application Case Study- Market Trend
Summary This article examines market trends and demand drivers for cosmetic factory cleanroom gel seal application case study, including industry growth factors, supplier selection criteria, and global adoption trends. 1 Introduction Cosmetic cleanroom HEPA gel seal case. Global demand for premium two-component jelly gel is growing at double digit rates, driven by cleanroom construction in semiconductors and biopharma, smart meter rollouts, automotive electronics electrification, and the...
Gel Seal Installation Pitfalls That Cause Cleanroom Leaks
Keywords: HY-9400 jelly gel, blue jelly potting gel, self healing silicone gel Summary This article provides a technical analysis of gel seal installation pitfalls that cause cleanroom leaks, covering material properties, installation procedures, key performance parameters, and quality assurance to support engineering and procurement decisions. 1 Introduction Gel Seal Installation Pitfalls That Cause Cleanroom Leaks - Technical Analysis This technical analysis examines the material...
Keywords: low shrinkage GRC mold silicone, high tear strength condensation silicone, RTV-2 tin-cure rubber, GRC component dimensional stability Key Sentence: Newly upgraded condensation-cure silicone formulas optimize molecular structure and reinforcing filler ratio, solving core pain points of large-size GRC mold shrinkage, deformation and short service life. Traditional general-purpose condensation silicone often suffers from obvious shrinkage, edge tearing and permanent deformation after...
Formula Upgrade Optimizes Tear Resistance & Shrinkage Performance for Hand‑Prototype Replica‑Molding Silicone Keywords: replica‑molding silicone formula iteration, low‑shrinkage condensation silicone, high tear strength, hand‑prototype duplication, mold cycle improvement Key sentence: Adjustments to polymer matrix and reinforcing fillers improve tear resistance and shrinkage control of condensation‑cure replica‑molding silicone, extending service life for repeated hand‑prototype casting...
Formula Iteration Improves Detail Reproduction & Anti‑Deformation Performance for Hand‑Model Condensation Silicone Keywords: hand‑model silicone formula upgrade, low‑shrinkage condensation‑cure silicone, fine‑detail replication, prototype mold dimensional stability Key sentence: Optimized polymer formula and reinforcing‑filler adjustment enhance detail capturing and shrinkage control, making condensation‑cure silicone better fit complex‑surface hand‑model prototype requirements....
Hongye Silicone Launches Low‑Outgassing Electronic Potting Silicone for Precision Sensor Protection
Keywords: Hongye Silicone, low outgassing potting silicone, sensor encapsulation compound, Huizhou silicone manufacturer Core Sentence: Hongye Silicone releases low‑outgassing electronic potting silicone with stable dielectric property, reducing volatile substance precipitation and delivering reliable encapsulation protection for high‑precision industrial sensors. On August 20, Hongye Silicone rolled out a new low‑outgassing two‑component addition‑cure potting silicone, responding to strict...
Growing Overseas Orders for Weather Resistant Foam Silicone
Growing Overseas Orders for Weather Resistant Foam Silicone, HONG YE SILICONE Stabilizes Batch Quality Supply Keywords: HONG YE SILICONE, weather resistant foam silicone, UV proof silicone foam, outdoor equipment sealing material Summary: The global outdoor electronics and photovoltaic industries generate steady demand for anti-aging and weatherproof sealing materials. HONG YE SILICONE gains continuous overseas orders for weather resistant foam silicone and strengthens quality control for...
Both condensation‑cure (tin‑catalyzed) and addition‑cure (platinum‑catalyzed) RTV‑2 silicone can produce molds for GRC, GRG, concrete and plaster decorative productsMade-in-Ch.... Addition‑cure silicone features ultra‑low shrinkage below 0.1%, no volatile by‑products, long mold lifespan, but its raw‑material price is 2‑3 times higher than condensation‑cure silicone, which restricts large‑scale application in low‑margin mass‑produced GRC European‑style components. Condensation‑cure silicone...
HONG YE SILICONE Anti-fatigue Foaming Silicone Delivers Stable Performance Under Repeated Compression Keywords: HONG YE SILICONE, anti-fatigue foaming silicone, repeated compression resistant, long-term buffer silicone foam Summary: Dynamic working scenarios with frequent vibration and repeated compression demand durable buffer materials. HONG YE SILICONE launches anti-fatigue foaming silicone that maintains consistent elasticity without permanent deformation after long-term cyclic...
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.